Concrete Sealer – Turns Standard Concrete Into an ESD Floor

Why waste a good concrete floor? Our Concrete Sealer turns any concrete floor into an ESD Floor and also makes it easier to maintain.

SKU: E-SEAL Categories: , ,


< $0.40 PSF


Today’s reality dictates an increasingly daunting task. When handling static sensitive product and to assure your successful manufacturing ESD flooring is a must! Yet does it make sense to pay $7.00 to 10.00 per installed square foot for ESD tiles, thick set ESD epoxy or an anti-static rubber floor? Most think NOT! ElectraSeal ESD Floor Sealer for Concrete seals concrete with an effective static control formulation and eliminates concrete dusting of the concrete slab for less than $.40 cents per square foot! ElectraSeal provides static control properties complaint for many ESD control programs.


Concrete Sealer Turns Standard Concrete into an ESD Floor!

ElectraSeal ESD Concrete Sealer is a floor sealer offering Value, Performance and Longevity. A typical concrete slab will post fairly good electrical conductivity due to the moisture content in the slabs. Unfortunately this electrical conductivity fluctuates dramatically with the ambient humidity and moisture content of the concrete. In addition, unsealed concrete is dusty, absorbs contaminants (such as oil and grime) and ends up being a time consuming maintenance nightmare!


Click here for Distribution Cut Sheet


Installation Overview
  • Best results are obtained when ElectraSeal ESD Sealer is applied to cured concrete surfaces which are 60 Deg F. or warmer and in relative humidity conditions of < 50%. Thoroughly vacuum slab to remove any loose dirt or dust. If contaminants such as oil and grease have soaked into the slab wash with Electra-Clean, rinse slab and allow to dry completely prior to application of ElectraSeal.
  • For best results apply three thin, even coats of ElectraSeal followed by one thin coat of ElectraGlaze using a using new loop end rayon or microfiber mop. Allow at least 2 hours of drying time between each coat.
  • Recoating may be achieved in the following manner. Vacuum the floor to remove any loose dirt or dust. Wash the floor with Electra-Clean. Apply a fresh, thin even coat of ElectraSeal. Allow it to dry for approximately 2 to 4 hours and apply a fresh coat of ElectraGlaze. See full installation instructions prior to installing this product.


Click HERE to Download Full Installation Instructions


ElectraSeal Routine Maintenance Procedure

ElectraSeal Concrete Sealer is an extremely durable ESD static dissipative concrete sealer. After application and curing of ElectraSeal routine maintenance (to be expected with any floor) is all that is required to maintain the luster and conductivity of the finish. It’s important to remove abrasives that can scratch and degrade the conductivity by dry mopping (usually on a daily basis). On an occasional basis (most of our clients prefer to do this once a week) wet mop the floor with a diluted mixture of ElectraClean and water and allow to dry.

ElectraClean works great with power scrubbing equipment or in hand mop applications. ElectraClean ESD Floor Sealer removes dirt and abrasives that dry mopping leaves behind and smells great too. Most cleaners and detergents leave behind harmful insulative residues reducing the conductivity of the ESD floor finish. Not so with ElectraClean! And, a little ElectraClean goes a long way. Typical dilution is 16 ounces of ElectraClean mixed with a gallon of water.


Click HERE to Download Full Maintenance Instructions


ESD Concrete Sealer Specifications
Spec Value
Nonvolatile Solids 25 +/- 0.6%
Total Active 30.1%
VOC Content 54.4 Grams per Liter see test results
Resistivity-ANSI S7.1 <1.0E09
Static Dissipation Anti Static to Static Conductive
pH 8.4 – 9.0
Gloss 60 0 80+ @ 3 coats
Color Translucent White
Weight per Gallon 10 lbs
Slip Resistance (ASTM) 0.65 Minimum
Stability 2 year minimum at room temperature
Freeze/Thaw Stability 3 cycles minimum
Drying Time 60 – 120 minutes
Water Resistance Good
Gallon Coverage (Feet 2) 1500 – 2000
Removability (Gardner) 75 cycles maximum


Click to Here to Download Full Specifications


ESD Concrete Sealer Safety Information
Spec Value
Health 1
Flammability 0
Reactivity 0
Personal Protection B


Click to Here to Download SDS Sheet



Facebook Page
All Products


There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.